当前位置:伯乐彩票APP下载-新闻中心 > 新闻中心

通风管道材料怎样选择才能好的效果

发布人:http://www。sftfgd。com   发布时间:2017-04-07 09:29:00

通风管道厂家对于风管制作过程中对材料的要求是相当有考究的,风管表面层为铝箔材质时,为确保表面层不易损坏,故对铝箔材质及厚度作出规定,并对铝箔与增强材料复合的风管表层的铝箔厚度作了规定。
Ventilation pipe manufacturers are quite sophisticated for the material requirements of the wind pipe production process, the wind pipe surface layer is an aluminum foil material, to ensure that the surface layer is not easy to damage, so the provisions of foil material and thickness, and the thickness of the aluminum foil and aluminum foil reinforced composite wind pipe surface has been specified。
其次,薄钢板法兰通风管道内、外表层和内部绝热材料粘接牢固,是保证复合材料的基本条件之一。超出一定面积的板材缺陷,不仅影响风管使用寿命,而且有时会降低其保温效果。所以缺陷不得大于6‰,以达到材料在系统中的正常使用。
Secondly, the inner layer, the outer layer and the internal thermal insulation material of the steel flanges are firmly bonded, which is one of the basic conditions of the composite material. Beyond a certain area of the plate defects, not only affect the service life of the wind pipe, and sometimes reduce its insulation effect. Therefore, the defect shall not be greater than 6 per thousand, in order to achieve the normal use of materials in the system.
目前,非金属风管材料发展较快,品种较多,困其具有的特性和优点,应用也越来越广泛。为了保证使用中的安全,对这些材料制作的风管提出了应按工程的需要具有不燃或难燃B1级的燃烧性能要求,而其表面层必须为不燃材料。
At present, the development of non metallic wind pipe material is faster, more varieties, and its characteristics and advantages, the application is more and more widely. In order to ensure the safety of the use of these materials produced by the wind pipe should be in accordance with the needs of the project is not flammable or difficult to burn B1 level of combustion performance requirements, and its surface layer must be non combustible material.
根据我国多年的工程应用实践与产品状况,规定了热敏胶带与压敏胶带的剥离强度试验较低值与铝箔厚度值;要求胶带宽度不应小于50mm,防止使用的胶带不能满足管壁密封的强度和风管使用年限。热敏胶带的优点是依靠热熔粘接,只要不在加热,在常温下胶面是固化的,具有牢靠的粘接强度。
According to the engineering practice and product status in China for many years, the provisions of the minimum value of the peel strength test of thermal tape and adhesive tape and foil thickness requirements; the tape width should not be less than 50mm, to prevent the tape can not be used to meet the sealing wall strength and wind period of use。 The advantage of heat sensitive adhesive tape is to rely on hot melt adhesive, as long as it is not heated, it is solidified at normal temperature。

上一篇:实验室通风系统的设计及使用特点
下一篇:金属管道材料在高温下使用作用

网站伯乐彩票APP下载 关于我们 产品展示 新闻中心 工程案例 在线留言 联系我们

百万彩票APP 河北快3开奖结果 必中彩票APP下载 必中彩票APP下载 奔驰彩票APP下载 河北快3走势图 河北快3走势图 宝马彩票APP下载 博牛彩票APP下载 伯乐彩票APP下载